bes2600: enable CONFIG_BES2600_TESTMODE by default + fix bit-rotted testmode plumbing

The driver implements a mac80211 testmode_cmd operation that dispatches
to a set of vendor commands (GET_TX_POWER_LEVEL, GET_TX_POWER_RANGE,
SET_SNAP_FRAME, TSM_STATS, GET_ROAM_DELAY, GET_STREAM, etc) plus the
BES2600 RF-test path (bes2600_vendor_rf_cmd → firmware
patch_wifi_testMode). The testmode handlers and the .testmode_cmd
binding in struct ieee80211_ops are conditionally compiled under
CONFIG_BES2600_TESTMODE, which previously defaulted to n.

Flip the Makefile default from n to y so wifi_testmode_cmd.o is
included in the build and the .testmode_cmd op is populated. On the
PineTab2 target kernel (linux-pinetab2 6.19.10-danctnix1, built with
CONFIG_NL80211_TESTMODE=y) this exposes the BES2600 RF-test surface
through the standard nl80211 testmode interface ('iw phy0 ...').

This also makes visible two classes of bit-rot that had accumulated
while nobody was building with CONFIG_BES2600_TESTMODE=y:

1. sta.c contains ~41 calls to bes2600_info() / bes2600_err() /
   bes2600_warn() / bes2600_dbg() / bes2600_err_with_cond() - a
   legacy log-macro family carrying a BES2600_DBG_* subsystem-id
   first argument. Neither the macros nor any of the BES2600_DBG_*
   constants are defined anywhere in the tree. The same call pattern
   appears under #if defined(BES2600_DETECTION_LOGIC) in hwio.c and
   under CONFIG_BES2600_ITP in itp.c, both normally disabled.

   Add minimal shim macros to bes_log.h that rewire the calls onto
   the existing bes_info() / bes_err() / bes_warn() / bes_devel()
   family (ignoring the subsystem id). Define BES2600_DBG_SBUS,
   BES2600_DBG_DOWNLOAD, BES2600_DBG_ITP and BES2600_DBG_TEST_MODE
   as 0 constants for documentation / grep.

2. bes2600_start_stop_tsm(), bes2600_get_tsm_params(), and
   bes2600_get_roam_delay() are declared in sta.c with external
   linkage but have no prototype in any header. All callers live in
   sta.c (inside bes2600_testmode_cmd). With CONFIG_BES2600_TESTMODE
   off the compiler never sees them; with it on gcc
   -Werror=missing-prototypes breaks the build.

   Mark the three functions static. (Keeping them file-local also
   matches their actual usage.)

Both changes are strictly scoped to make CONFIG_BES2600_TESTMODE=y
buildable; no behavioural change when the flag is off.

Tested-on: PineTab2 (BES2600WM + RK3566) running linux-pinetab2
6.19.10-danctnix1-1 with CONFIG_NL80211_TESTMODE=y. Module builds
cleanly, nl80211 testmode interface reachable via 'iw phy0 ...' from
userspace.

Signed-off-by: Markus Fritsche <fritsche.markus@gmail.com>

bes2600/Makefile

@@ -28,6 +28,7 @@ CONFIG_BES2600_WIFI_BOOT_ON             ?= y
 CONFIG_BES2600_BT_BOOT_ON               ?= n
 
 BES2600_GPIO_WAKEUP_AP                  ?= n
+BES2600_WRITE_DPD_TO_FILE               ?= n
 BES2600_TX_MORE_RETRY                   ?= n
 
 # bes evb
@@ -64,8 +65,8 @@ BES2600_DRV_VERSION := bes2600_0.3.5_2024.0116
 
 ifeq ($(CONFIG_BES2600_CALIB_FROM_LINUX),y)
 FACTORY_CRC_CHECK                    ?= n
-STANDARD_FACTORY_EFUSE_FLAG          ?= n
+STANDARD_FACTORY_EFUSE_FLAG          ?= y
-FACTORY_PATH                 ?= bes2600/bes2600_factory.txt
+FACTORY_PATH                 ?= /lib/firmware/bes2600_factory.txt
 endif
 
 # basic function
@@ -92,6 +93,12 @@ ccflags-y += -DBES_UNIFIED_PM
 ccflags-y += -DBES_SDIO_OPTIMIZED_LEN
 ccflags-y += -DBES2600_HOST_TIMESTAMP_DEBUG
 
+ifeq ($(BES2600_WRITE_DPD_TO_FILE),y)
+BES2600_DPD_PATH ?= /data/cfg/bes2600_dpd.bin
+BES2600_DEFAULT_DPD_PATH ?= /lib/firmware/bes2600_dpd.bin
+BES2600_DPD_GOLDEN_PATH ?= /data/cfg/bes2600_dpd_golden.bin
+endif
+
 ifeq ($(BES2600_DUMP_FW_DPD_LOG),y)
 BES2600_DPD_LOG_PATH ?= /data/applog/bes2600_dpd_log.log
 endif
@@ -128,6 +135,9 @@ ccflags-y += $(call boolen_flag,BSS_LOSS_CHECK,y)
 ccflags-y += $(call string_flag,BES2600_LOAD_FW_TOOL_PATH)
 ccflags-y += $(call string_flag,BES2600_LOAD_FW_TOOL_DEVICE)
 ccflags-y += $(call string_flag,BES2600_DRV_VERSION)
+ccflags-y += $(call string_flag,BES2600_DPD_PATH)
+ccflags-y += $(call string_flag,BES2600_DEFAULT_DPD_PATH)
+ccflags-y += $(call string_flag,BES2600_DPD_GOLDEN_PATH)
 
 ccflags-y += $(call boolen_flag,BES2600_INDEPENDENT_EVB,y)
 ccflags-y += $(call boolen_flag,BES2600_INTEGRATED_MODULE_V1,y)
@@ -149,6 +159,8 @@ ccflags-y += $(call boolen_flag,FACTORY_SAVE_MULTI_PATH,y)
 ccflags-y += $(call boolen_flag,FACTORY_CRC_CHECK,y)
 
 ccflags-y += $(call boolen_flag,BES2600_GPIO_WAKEUP_AP,y)
+ccflags-y += $(call boolen_flag,BES2600_WRITE_DPD_TO_FILE,y)
+
 ccflags-y += $(call boolen_flag,BES2600_DUMP_FW_DPD_LOG,y)
 ccflags-y += $(call string_flag,BES2600_DPD_LOG_PATH)
 

bes2600/bes2600_factory.c

@@ -12,7 +12,6 @@
 #include <linux/module.h>
 #include <linux/sched.h>
 #include <linux/fs.h>
-#include <linux/firmware.h>
 #include <linux/slab.h>
 #include <linux/mutex.h>
 #include <linux/crc32.h>
@@ -31,18 +30,6 @@
 
 static DEFINE_MUTEX(factory_lock);
 
-/*
- * struct device * for request_firmware() context. Set once at SDIO
- * probe via bes2600_factory_set_dev(). NULL is tolerated (falls back
- * to the udev-less firmware-class path) but loses per-device logging.
- */
-static struct device *bes2600_factory_dev;
-
-void bes2600_factory_set_dev(struct device *dev)
-{
-	bes2600_factory_dev = dev;
-}
-
 /*
  * It is only used for temporary storage.
  * Every time get the factory, it will read from the
@@ -150,32 +137,66 @@ static int bes2600_factory_crc_check(struct factory_t *factory_data)
  */
 static int factory_section_read_file(char *path, void *buffer)
 {
-	const struct firmware *fw;
+	int ret = 0;
-	int ret;
+	struct file *fp;
 
 	if (!path || !buffer) {
 		bes_err("%s NULL pointer err\n", __func__);
 		return -1;
 	}
 
-	bes_devel("requesting firmware-class %s\n", path);
+	bes_devel("reading %s \n", path);
 
-	ret = request_firmware(&fw, path, bes2600_factory_dev);
+	fp = filp_open(path, O_RDONLY, 0); //S_IRUSR
-	if (ret) {
+	if (IS_ERR(fp)) {
-		bes_devel("BES2600: request_firmware(%s) failed: %d\n", path, ret);
+		bes_devel("BES2600 : can't open %s\n",path);
 		return -1;
 	}
 
-	if (fw->size == 0 || fw->size > FACTORY_MAX_SIZE) {
+	if (fp->f_inode->i_size <= 0 || fp->f_inode->i_size > FACTORY_MAX_SIZE) {
-		bes_err("bes2600_factory.txt size check failed, read_size: %zu max_size: %d\n",
+		bes_err(			"bes2600_factory.txt size check failed, read_size: %lld max_size: %d\n",
-			fw->size, FACTORY_MAX_SIZE);
+			fp->f_inode->i_size, FACTORY_MAX_SIZE);
-		release_firmware(fw);
+		filp_close(fp, NULL);
 		return -1;
 	}
 
-	memcpy(buffer, fw->data, fw->size);
+	ret = kernel_read(fp, buffer, fp->f_inode->i_size, &fp->f_pos);
-	ret = (int)fw->size;
+
-	release_firmware(fw);
+	filp_close(fp, NULL);
+
+	if (ret != fp->f_inode->i_size) {
+		bes_err("bes2600_factory.txt read fail\n");
+		ret = -1;
+	}
+
+	return ret;
+}
+
+/**
+ * factory_section_write_file - Write data of specified length to file
+ * @path:	path of the file
+ * @buffer:	storage of write data
+ * @size:	length of data to write
+ *
+ * Return: length on success, negative error code otherwise.
+ */
+static int factory_section_write_file(char *path, void *buffer, int size)
+{
+	int ret = 0;
+	struct file *fp;
+
+	bes_devel("writing %s \n", path);
+
+	fp = filp_open(path, O_TRUNC | O_CREAT | O_RDWR, S_IRUSR);
+	if (IS_ERR(fp)) {
+		bes_devel("BES2600 : can't open %s\n",path);
+		return -1;
+	}
+
+	ret = kernel_write(fp, buffer, size, &fp->f_pos);
+
+	filp_close(fp,NULL);
+
 	return ret;
 }
 
@@ -870,22 +891,9 @@ static inline int factory_build(uint8_t *dest_buf, struct factory_t *factory)
 #endif
 }
 
-/*
- * Rebuild the serialised calibration blob in file_buffer from the live
- * in-memory factory_save_p. Previously this function also persisted the
- * blob back to FACTORY_PATH via filp_open(O_CREAT) + kernel_write(); that
- * is not acceptable in mainline, so the persistence step has been removed.
- *
- * The in-memory factory_save_p remains authoritative for the duration of
- * the session; on the next probe the firmware-class file is read back
- * read-only via request_firmware(). If cross-reboot persistence of runtime
- * calibration updates becomes a requirement, the expected route is a
- * userspace-facing dump interface (debugfs read-only blob, or nl80211
- * vendor command) that lets userspace read the serialised form and store
- * it under its own privileges.
- */
 static int bes2600_wifi_cali_table_save(u8 *file_buffer, struct factory_t *factory_save_p)
 {
+	int ret = 0;
 	int w_size;
 	u32 crc_len = sizeof(factory_data_t);
 #ifndef STANDARD_FACTORY_EFUSE_FLAG
@@ -894,11 +902,13 @@ static int bes2600_wifi_cali_table_save(u8 *file_buffer, struct factory_t *facto
 
 	bes_devel("enter %s\n", __func__);
 
-	if (!file_buffer)
+	if (!file_buffer) {
 		return -ENOMEM;
+	}
 
-	if (!factory_save_p)
+	if (!factory_save_p) {
 		return -ENOENT;
+	}
 
 	/* All initialized to space */
 	memset(file_buffer, 32, FACTORY_MAX_SIZE);
@@ -910,10 +920,22 @@ static int bes2600_wifi_cali_table_save(u8 *file_buffer, struct factory_t *facto
 	w_size = factory_build(file_buffer, factory_save_p);
 
 	if (w_size < 0 || w_size > FACTORY_MAX_SIZE) {
-		bes_err("%s: build failed! w_size = %d.", __func__, w_size);
+		bes_err("%s: build failed! ret = %d.", __func__, ret);
 		return -ETXTBSY;
 	}
 
+#ifdef FACTORY_SAVE_MULTI_PATH
+	/* avoid trailing characters '\0' */
+	file_buffer[w_size] = 32;
+	ret = factory_section_write_file(FACTORY_PATH, file_buffer, FACTORY_MAX_SIZE);
+#else
+	ret = factory_section_write_file(FACTORY_PATH, file_buffer, w_size);
+#endif
+	if(ret < 0) {
+		bes_err("%s: write failed! ret = %d.", __func__, ret);
+		return ret;
+	}
+
 	return 0;
 }
 

bes2600/bes2600_factory.h

@@ -199,9 +199,6 @@ enum factory_cali_status {
 /* just calibrate 11n, other protocols are automatically mapped */
 #define WIFI_RF_11N_MODE 0x15
 
-/* set the struct device * used for request_firmware() context */
-void bes2600_factory_set_dev(struct device *dev);
-
 /* read wifi & bt factory cali value*/
 u8* bes2600_get_factory_cali_data(u8 *file_buffer, u32 *data_len, char *path);
 void factory_little_endian_cvrt(u8 *data);

bes2600/bes2600_sdio.c

@@ -16,7 +16,6 @@
 #include <linux/mmc/host.h>
 #include <linux/mmc/sdio_func.h>
 #include <linux/mmc/card.h>
-#include <linux/mmc/core.h>
 #include <linux/mmc/sdio.h>
 #include <linux/spinlock.h>
 #include <net/mac80211.h>
@@ -31,7 +30,6 @@
 #include "bes2600.h"
 #include "sbus.h"
 #include "bes2600_plat.h"
-#include "bes2600_factory.h"
 #include "hwio.h"
 #include "bes_chardev.h"
 #include "bes_log.h"
@@ -96,7 +94,6 @@ struct sbus_priv {
 	struct work_struct tx_work;
 	struct scatterlist tx_sg[BES_SDIO_TX_MULTIPLE_NUM + 1];
 	struct scatterlist tx_sg_nosignal[BES_SDIO_TX_MULTIPLE_NUM_NOSIGNAL + 1];
-	u8 *tx_bounce;
 	u32 tx_data_cnt;
 	u32 tx_xfer_cnt;
 	u32 tx_proc_cnt;
@@ -1138,26 +1135,7 @@ static void sdio_tx_work(struct work_struct *work)
 				}
 			}
 
-			/*
+			sg_set_buf(&sg[scatters], tx_buffer->buf, align);
-			 * The transfer length is rounded up to the SDIO block
-			 * size, but tx_buffer->buf is only tx_buffer->len bytes
-			 * long (it usually aliases into an skb linear head).
-			 * Copy into a driver-owned bounce buffer and zero-pad
-			 * to the aligned size; otherwise DMA reads past the
-			 * skb and leaks adjacent kernel memory on the wire --
-			 * observed as KFENCE OOB reads from
-			 * bes_sdio_memcpy_to_io_helper via dma_map_sg.
-			 */
-			if (WARN_ON_ONCE(total_len + align > MAX_SDIO_TRANSFER_LEN))
-				goto flush_previous;
-			memcpy(self->tx_bounce + total_len,
-			       tx_buffer->buf, tx_buffer->len);
-			if (align > tx_buffer->len)
-				memset(self->tx_bounce + total_len +
-				       tx_buffer->len, 0,
-				       align - tx_buffer->len);
-			sg_set_buf(&sg[scatters],
-				   self->tx_bounce + total_len, align);
 			total_len += align;
 			++scatters;
 /*del_node:*/
@@ -1778,33 +1756,6 @@ static void bes2600_sdio_halt_device(struct sbus_priv *self)
 	sdio_work_debug(self);
 }
 
-/*
- * Trigger an SDIO bus reset via mmc_hw_reset().
- *
- * With multiple SDIO functions probed (PineTab2 binds func 1 for WLAN and
- * func 2 for the BT-companion path) mmc_sdio_hw_reset() takes the
- * remove-and-rescan path: it marks the card removed and schedules
- * mmc_rescan, which tears down the bound function drivers and re-detects
- * the card on the next sweep, in turn reinvoking bes2600_sdio_probe().
- *
- * With a single function probed it instead invokes mmc_power_cycle()
- * directly, which on PineTab2 toggles the wifi-reset GPIO via sdio_pwrseq.
- *
- * In both cases the chip ends up in a freshly reset state, which is the
- * goal of the recovery path.
- *
- * mmc_hw_reset() must be called without holding the SDIO host claim --
- * the multi-func remove-and-rescan path acquires the host claim via the
- * mmc workqueue.
- */
-static int bes2600_sdio_bus_reset(struct sbus_priv *self)
-{
-	if (!self || !self->func || !self->func->card)
-		return -EINVAL;
-
-	return mmc_hw_reset(self->func->card);
-}
-
 static bool bes2600_sdio_wakeup_source(struct sbus_priv *self)
 {
 	struct bes2600_platform_data_sdio *pdata = bes2600_get_platform_data();
@@ -1843,7 +1794,6 @@ static struct sbus_ops bes2600_sdio_sbus_ops = {
 	.gpio_sleep		= bes2600_gpio_allow_mcu_sleep,
 	.halt_device		= bes2600_sdio_halt_device,
 	.wakeup_source		= bes2600_sdio_wakeup_source,
-	.bus_reset		= bes2600_sdio_bus_reset,
 };
 
 static void bes2600_sdio_en_lp_cb(struct bes2600_common *hw_priv)
@@ -1884,9 +1834,6 @@ static int bes2600_sdio_probe(struct sdio_func *func,
 	if (ret)
 		goto err;
 
-	/* wire struct device into factory.c for request_firmware() context */
-	bes2600_factory_set_dev(dev);
-
 	self->pdata = bes2600_get_platform_data();
 	self->func = func;
 	self->dev = &func->dev;
@@ -1906,17 +1853,6 @@ static int bes2600_sdio_probe(struct sdio_func *func,
 	if (!self->single_gathered_buffer)
 		return -ENOMEM;
 #endif
-#ifdef BES_SDIO_TX_MULTIPLE_ENABLE
-	self->tx_bounce = (u8 *)__get_dma_pages(GFP_KERNEL,
-					get_order(MAX_SDIO_TRANSFER_LEN));
-	if (!self->tx_bounce) {
-#ifndef SDIO_HOST_ADMA_SUPPORT
-		free_pages((unsigned long)self->single_gathered_buffer,
-			   get_order(MAX_SDIO_TRANSFER_LEN));
-#endif
-		return -ENOMEM;
-	}
-#endif
 #ifdef BES_SDIO_RXTX_TOGGLE
 	self->fw_started = false;
 #endif
@@ -2045,12 +1981,6 @@ static void bes2600_sdio_remove(struct sdio_func *func)
 		if (self->single_gathered_buffer) {
 			free_pages((unsigned long)self->single_gathered_buffer, get_order(MAX_SDIO_TRANSFER_LEN));
 		}
-#endif
-#ifdef BES_SDIO_TX_MULTIPLE_ENABLE
-		if (self->tx_bounce) {
-			free_pages((unsigned long)self->tx_bounce,
-				   get_order(MAX_SDIO_TRANSFER_LEN));
-		}
 #endif
 		kfree(self);
 	}

bes2600/bes_chardev.c

@@ -43,6 +43,12 @@ enum bus_probe_state {
 };
 
 struct bes_cdev {
+	struct cdev cdev;
+	dev_t dev_id;
+	int major;
+	int minor;
+	struct class *class;
+	struct device *device;
 	atomic_t num_proc;
 	wait_queue_head_t open_wq;
 	spinlock_t status_lock;
@@ -63,6 +69,9 @@ struct bes_cdev {
 	struct delayed_work probe_timeout_work;
 	enum bus_probe_state bus_probe;
 	struct work_struct wifi_force_close_work;
+#ifdef BES2600_WRITE_DPD_TO_FILE
+	int no_dpd;
+#endif
 	enum pend_read_op read_flag;
 	enum wakeup_event wakeup_by_event;	/* used to filter unwanted event wakeup reason report */
 	u16 wakeup_state; /* for userspace check wakeup reason */
@@ -82,6 +91,9 @@ struct bes2600_op_map {
 
 static struct bes_cdev bes2600_cdev;
 module_param_named(fw_type, bes2600_cdev.fw_type, int, 0644);
+#ifdef BES2600_WRITE_DPD_TO_FILE
+module_param_named(no_dpd, bes2600_cdev.no_dpd, int, 0644);
+#endif
 
 extern int bes2600_register_net_dev(struct sbus_priv *bus_priv);
 extern int bes2600_unregister_net_dev(struct sbus_priv *bus_priv);
@@ -237,18 +249,351 @@ int bes2600_switch_bt(bool on)
 	return ret;
 }
 
+static int bes2600_get_cmd_and_ifname(const char *str, char **result)
+{
+	int cmd_len = 0;
+	int ifname_len = 0;
+	char *sp = NULL;
+	char *tmp_ptr = NULL;
+	char *cmd_ptr = NULL;
+
+	/* check if input arguments is valid */
+	if (!str || strncmp(str, "ifname:", 7) != 0)
+		return -1;
+
+	sp = strchr(str, ' ');
+	if (strncmp(sp + 1, "cmd:", 4) != 0)
+		return -1;
+
+	/* extract interface name */
+	ifname_len = sp - str - 7;
+	tmp_ptr = kmalloc(ifname_len + 1, GFP_KERNEL);
+	if (!tmp_ptr) {
+		return -2;
+	}
+
+	strncpy(tmp_ptr, str+7, ifname_len);
+	tmp_ptr[ifname_len] = '\0';
+	result[0] = tmp_ptr;
+
+	/* get command length */
+	cmd_ptr = strstr(str, "cmd:");
+	cmd_ptr += 4;
+	sp = strchr(cmd_ptr, ' ');
+	if (!sp) {	/* the command don't have any parameter */
+		cmd_len = strlen(cmd_ptr);
+		if (cmd_ptr[cmd_len - 1] == '\n')
+			--cmd_len;
+	} else {	/* the command have one or more parameter */
+		cmd_len = sp - cmd_ptr;
+	}
+
+	/* copy command to out buffer */
+	tmp_ptr = kmalloc( cmd_len + 1, GFP_KERNEL);
+	if (!tmp_ptr) {
+		kfree(result[0]);
+		result[0] = NULL;
+		return -3;
+	}
+
+	strncpy(tmp_ptr, cmd_ptr, cmd_len);
+	tmp_ptr[cmd_len] = '\0';
+	result[1] = tmp_ptr;
+
+	return 0;
+}
+
+static void bes2600_recyle_cmd_and_ifname_mem(char **info)
+{
+	if (info[0]) {
+		kfree(info[0]);
+		info[0] = NULL;
+	}
+
+	if (info[1]) {
+		kfree(info[1]);
+		info[1] = NULL;
+	}
+
+}
+
+static int bes2600_op_default_handler(const char *str)
+{
+	char *info[2] = {0};
+
+	if (bes2600_get_cmd_and_ifname(str, info) == 0) {
+		bes_devel("cmd(%s) on %s not handled\n", info[1], info[0]);
+	} else {
+		bes_err("%s get command fail, the origin string is %s\n", __func__, str);
+	}
+
+	bes2600_recyle_cmd_and_ifname_mem(info);
+
+	return 0;
+}
+
+static int bes2600_op_wifi_bt_on_off(const char *str)
+{
+	char *info[2] = {0};
+	int ret = 0;
+	enum wait_state wait_state;
+	enum bus_probe_state probe_state;
+	unsigned long status = 0;
+
+	spin_lock(&bes2600_cdev.status_lock);
+	probe_state = bes2600_cdev.bus_probe;
+	wait_state = bes2600_cdev.wait_state;
+	spin_unlock(&bes2600_cdev.status_lock);
+
+	/* only work for wifi signal mode */
+	if (bes2600_cdev.fw_type != BES2600_FW_TYPE_WIFI_SIGNAL)
+		return -EFAULT;
+
+	/* wait bus probe operation end */
+	if (probe_state == BES2600_BUS_PROBE_START) {
+		bes_devel("wait bus probe operation end\n");
+		status = wait_event_timeout(bes2600_cdev.probe_done_wq,
+					(bes2600_cdev.bus_probe > BES2600_BUS_PROBE_START),
+					HZ);
+		WARN_ON(status <= 0);
+	}
+
+	/* must wait previous operation end in critical section */
+	if (wait_state != BES2600_BOOT_WAIT_NONE) {
+		bes_devel("wait previous operation end\n");
+		status = wait_event_timeout(bes2600_cdev.probe_done_wq,
+					(bes2600_cdev.wait_state == BES2600_BOOT_WAIT_NONE),
+					HZ * 8);
+		WARN_ON(status <= 0);
+	}
+
+	/* if dpd calibration is doing, modify wifi and bt state directly */
+	spin_lock(&bes2600_cdev.status_lock);
+	if (bes2600_cdev.bus_probe == BES2600_BUS_PROBE_OK && !bes2600_cdev.dpd_calied) {
+		if (bes2600_get_cmd_and_ifname(str, info) == 0) {
+			if (strncmp(info[1], "WIFI_ON", 7) == 0) {
+				bes2600_cdev.wifi_opened = true;
+			} else if (strncmp(info[1], "WIFI_OFF", 8) == 0) {
+				bes2600_cdev.wifi_opened = false;
+			} else if (strncmp(info[1], "BT_ON", 5) == 0) {
+				bes2600_cdev.bt_opened = true;
+				bes2600_cdev.bton_pending = true;
+			} else if (strncmp(info[1], "BT_OFF", 6) == 0) {
+				bes2600_cdev.bt_opened = false;
+				bes2600_cdev.bton_pending = false;
+			}
+		}
+		bes2600_recyle_cmd_and_ifname_mem(info);
+		spin_unlock(&bes2600_cdev.status_lock);
+
+		/* wait probe done event */
+		status = wait_event_timeout(bes2600_cdev.probe_done_wq,
+				bes2600_bootup_end(), HZ * 8);
+		WARN_ON(status <= 0);
+
+		return (status <= 0 || bes2600_chrdev_is_bus_error()) ? -EFAULT : 0;
+	}
+	spin_unlock(&bes2600_cdev.status_lock);
+
+	/* process wifi/bt on/off operation */
+	if (bes2600_get_cmd_and_ifname(str, info) == 0) {
+		if (strncmp(info[1], "WIFI_ON", 7) == 0) {
+			ret = bes2600_switch_wifi(1);
+		} else if (strncmp(info[1], "WIFI_OFF", 8) == 0) {
+			ret = bes2600_switch_wifi(0);
+		} else if (strncmp(info[1], "BT_ON", 5) == 0) {
+			ret = bes2600_switch_bt(1);
+		} else if (strncmp(info[1], "BT_OFF", 6) == 0) {
+			ret = bes2600_switch_bt(0);
+		}
+	}
+
+	if (!ret && bes2600_chrdev_check_system_close())
+		ret = bes2600_chrdev_do_system_close(bes2600_cdev.sbus_ops,
+						bes2600_cdev.sbus_priv);
+
+	bes2600_recyle_cmd_and_ifname_mem(info);
+
+	return ret ;
+}
 
 
+static int bes2600_op_change_fw_type(const char *str)
+{
+	int ret = 0;
+	int temp = 0;
+	long status = 0;
+	char *cmd_ptr = NULL;
+	char fw_type[5] = {0};
+	bool sys_closed = bes2600_chrdev_check_system_close();
+
+	bes_devel("%s is called, arg:%s\n", __func__, str);
+
+	if (!bes2600_cdev.sbus_ops->power_switch && !bes2600_cdev.sbus_ops->reboot)
+		return -EPERM;
+
+	/* check if user input is valid */
+	cmd_ptr = strstr(str, "CHANGE_FW_TYPE ");
+	if (strlen(str) < 16 || !cmd_ptr) {
+		bes_err("the format of \"%s\" is error\n", str);
+		return -EINVAL;
+	}
+
+	/* convert fw_type from string to int */
+	strncpy(fw_type, cmd_ptr + 14, 4);
+	fw_type[0] = '+';
+	ret = kstrtoint(fw_type, 10, &temp);
+	if (ret < 0) {
+		bes_err("%s parse error\n", __func__);
+		return -EINVAL;
+	}
+
+	/* no need to realod firmware if new fw_type is equal to the old */
+	if (temp == bes2600_cdev.fw_type ) {
+		bes_devel("fw type is equal\n");
+		return 0;
+	}
+
+	/* close wifi net device */
+	if (bes2600_cdev.sbus_priv
+	    && bes2600_is_net_dev_created(bes2600_cdev.sbus_priv)) {
+		bes2600_unregister_net_dev(bes2600_cdev.sbus_priv);
+	}
+
+	/* update firmware type */
+	bes2600_cdev.fw_type = temp;
+	bes2600_chrdev_update_signal_mode();
+
+	if (!sys_closed) {
+		/* close device to call disconnect function */
+		if (bes2600_cdev.sbus_ops->power_switch)
+			bes2600_cdev.sbus_ops->power_switch(bes2600_cdev.sbus_priv, 0);
+		else if (bes2600_cdev.sbus_ops->reboot)
+			bes2600_cdev.sbus_ops->reboot(bes2600_cdev.sbus_priv);
+	}
+
+	if (bes2600_cdev.sbus_ops->reboot)
+		bes2600_chrdev_start_bus_probe();
+
+	/* wait disconnect event */
+	status = wait_event_timeout(bes2600_cdev.probe_done_wq, (bes2600_cdev.sbus_priv == NULL), HZ * 10);
+	WARN_ON(status <= 0);
+
+	if (bes2600_cdev.dpd_calied
+	   && bes2600_chrdev_check_system_close()) {
+		bes_devel("no need to reload firmware\n");
+		return 0;
+	}
+
+	bes_devel("reload firmware...\n");
+	/* power on device to call probe function */
+	if (bes2600_cdev.sbus_ops->power_switch)
+		bes2600_cdev.sbus_ops->power_switch(NULL, 1);
+
+	/* wait probe done event */
+	status = wait_event_timeout(bes2600_cdev.probe_done_wq,
+			bes2600_bootup_end(), HZ * 10);
+	WARN_ON(status <= 0);
+
+	ret = (status <= 0 || bes2600_chrdev_is_bus_error()) ? -1 : 0;
 
 
+	return ret;
+}
 
+static int bes2600_op_bt_wakeup(const char *str)
+{
+	int ret = 0;
+	unsigned long status = 0;
 
+	spin_lock(&bes2600_cdev.status_lock);
+	if (!bes2600_cdev.bt_opened) {
+		spin_unlock(&bes2600_cdev.status_lock);
+		return -EFAULT;
+	}
+	spin_unlock(&bes2600_cdev.status_lock);
 
+	/* wait probe done event */
+	status = wait_event_timeout(bes2600_cdev.probe_done_wq,
+			bes2600_bootup_end(), HZ * 8);
+	if (status <= 0 || bes2600_chrdev_is_bus_error())
+		return -EFAULT;
 
+	bes_devel("bes2600 wakeup bt.\n");
+	ret = bes2600_chrdev_switch_subsys(GPIO_WAKE_FLAG_BT_LP_ON, SUBSYSTEM_BT_LP, true);
+
+	return ret;
+}
+
+static int bes2600_op_bt_sleep(const char *str)
+{
+	int ret = 0;
+	unsigned long status = 0;
+
+	spin_lock(&bes2600_cdev.status_lock);
+	if (!bes2600_cdev.bt_opened) {
+		spin_unlock(&bes2600_cdev.status_lock);
+		return -EFAULT;
+	}
+	spin_unlock(&bes2600_cdev.status_lock);
+
+	/* wait probe done event */
+	status = wait_event_timeout(bes2600_cdev.probe_done_wq,
+			bes2600_bootup_end(), HZ * 8);
+	if (status <= 0 || bes2600_chrdev_is_bus_error())
+		return -EFAULT;
+
+	bes_devel("bes2600 allow bt sleep.\n");
+	ret = bes2600_chrdev_switch_subsys(GPIO_WAKE_FLAG_BT_LP_OFF, SUBSYSTEM_BT_LP, false);
+
+	return ret;
+}
+
+static int bes2600_op_set_wakeup_read_flag(const char *str)
+{
+	bes_devel("%s is called, arg:%s\n", __func__, str);
+	spin_lock(&bes2600_cdev.status_lock);
+	bes2600_cdev.read_flag = BES_CDEV_READ_WAKEUP_STATE;
+	spin_unlock(&bes2600_cdev.status_lock);
+
+	return 0;
+}
 
 #ifdef FW_DOWNLOAD_UART_DAEMON
+int bes2600_load_uevent(char *env[])
+{
+	return kobject_uevent_env(&bes2600_cdev.device->kobj, KOBJ_CHANGE, env);
+}
 #endif
 
+static struct bes2600_op_map bes2600_op_map_tab[] ={
+	/*op			op_len	handler				*/
+	{"P2P_SET_NOA", 	11,	bes2600_op_default_handler},
+	{"P2P_SET_PS", 		10,	bes2600_op_default_handler},
+	{"SET_AP_WPS_P2P_IE",	17, 	bes2600_op_default_handler},
+	{"LINKSPEED", 		9,	bes2600_op_default_handler},
+	{"RSSI",		4,	bes2600_op_default_handler},
+	{"GETBAND", 		7,	bes2600_op_default_handler},
+	{"WLS_BATCHING", 	12,	bes2600_op_default_handler},
+	{"MACADDR",		7,	bes2600_op_default_handler},
+	{"RXFILTER-START",	14,	bes2600_op_default_handler},
+	{"RXFILTER-STOP",	13,	bes2600_op_default_handler},
+	{"RXFILTER-ADD",	12,	bes2600_op_default_handler},
+	{"RXFILTER-REMOVE",	15,	bes2600_op_default_handler},
+	{"BTCOEXMODE",		10,	bes2600_op_default_handler},
+	{"BTCOEXSCAN-START",	16,	bes2600_op_default_handler},
+	{"BTCOEXSCAN-STOP",	15,	bes2600_op_default_handler},
+	{"SETSUSPENDMODE",	14,	bes2600_op_default_handler},
+	{"COUNTRY",		7,	bes2600_op_default_handler},
+	{"WIFI_ON", 		7,	bes2600_op_wifi_bt_on_off},
+	{"WIFI_OFF", 		8,	bes2600_op_wifi_bt_on_off},
+	{"BT_ON", 		5,	bes2600_op_wifi_bt_on_off},
+	{"BT_OFF", 		6,	bes2600_op_wifi_bt_on_off},
+	{"CHANGE_FW_TYPE",	14,	bes2600_op_change_fw_type},
+	{"BT_WAKEUP",		9,	bes2600_op_bt_wakeup},
+	{"BT_SLEEP",		8,	bes2600_op_bt_sleep},
+	{"WAKEUP_STATE",	12,	bes2600_op_set_wakeup_read_flag},
+};
 
 static int bes2600_chrdev_check_system_close_internal(void)
 {
@@ -258,13 +603,255 @@ static int bes2600_chrdev_check_system_close_internal(void)
 		&& (bes2600_cdev.wifi_opened == false);
 }
 
+static int bes2600_chrdev_open(struct inode *inode, struct file *filp)
+{
+	if (atomic_read(&bes2600_cdev.num_proc) > 0) {
+		wait_event_timeout(bes2600_cdev.open_wq,
+			(atomic_read(&bes2600_cdev.num_proc) == 0),
+			MAX_SCHEDULE_TIMEOUT);
+	}
 
+	bes_devel("bes2600 char device is opened\n");
+	atomic_inc(&bes2600_cdev.num_proc);
 
+        return 0;
+}
 
+static ssize_t bes2600_chrdev_read(struct file *file, char __user *user_buf,
+			     size_t count, loff_t *ppos)
+{
+	char buf[64] = {0};
+	unsigned int len;
+	long status = 0;
 
+	switch (bes2600_cdev.read_flag) {
+	case BES_CDEV_READ_WAKEUP_STATE:
+		if (bes2600_chrdev_wakeup_by_event_get() > WAKEUP_EVENT_NONE) {
+			status = wait_event_timeout(bes2600_cdev.wakeup_reason_wq,
+				bes2600_chrdev_wakeup_by_event_get() ==  WAKEUP_EVENT_NONE, HZ * 2);
+			WARN_ON(status <= 0);
+		}
+		len = sprintf(buf, "wakeup_reason: %u, src_port: %u\n",
+		              bes2600_cdev.wakeup_state, bes2600_cdev.src_port);
+		break;
+	default:
+		len = sprintf(buf, "dpd_calied:%d wifi_opened:%d bt_opened:%d fw_type:%d\n",
+				bes2600_cdev.dpd_calied,
+				bes2600_cdev.wifi_opened,
+				bes2600_cdev.bt_opened,
+				bes2600_cdev.fw_type);
+		break;
+	}
+
+	len = sizeof(buf);
+	/* reset read flag */
+	spin_lock(&bes2600_cdev.status_lock);
+	bes2600_cdev.read_flag = BES_CDEV_READ_NUM_MAX;
+	spin_unlock(&bes2600_cdev.status_lock);
+
+	return simple_read_from_buffer(user_buf, count, ppos, buf, len);
+}
+
+static ssize_t bes2600_chrdev_write(struct file *file,
+		 const char __user *user_buf, size_t count, loff_t *ppos)
+{
+	int i = 0;
+	int cmd_num = ARRAY_SIZE(bes2600_op_map_tab);
+	int cmd_len = 0;
+	int ret = 0;
+	char *info[2] = {0};
+	char *buf = NULL;
+
+	/* copy content from user space to kernel */
+	/* message format:"ifname:wlanx cmd:xxx arg1 arg2 ..." */
+	buf = kmalloc(count + 1, GFP_KERNEL);
+	if (copy_from_user(buf, user_buf, count))
+		return -EFAULT;
+
+	/* add terminal character */
+	buf[count] = '\0';
+
+	/* extract comand and interface */
+	if (bes2600_get_cmd_and_ifname(buf, info) != 0) {
+		bes_err("%s get command fail, the origin string is %s\n", __func__, buf);
+		kfree(buf);
+		return -EINVAL;
+	}
+
+	/* match operation item and execure its handler */
+	cmd_len = strlen(info[1]);
+	for (i = 0; i < cmd_num; i++) {
+		if (cmd_len < bes2600_op_map_tab[i].op_len)
+			continue;
+
+		if (strncasecmp(info[1], bes2600_op_map_tab[i].op, bes2600_op_map_tab[i].op_len) == 0) {
+			ret = bes2600_op_map_tab[i].handler(buf);
+			break;
+		}
+	}
+
+	/* operation item mismatch */
+	if (i == cmd_num) {
+		bes_err("cmd(%s) mismatch\n", info[1]);
+	}
+
+	bes2600_recyle_cmd_and_ifname_mem(info);
+	kfree(buf);
+
+	return (ret == 0) ? count : ret;
+}
+
+static int bes2600_chrdev_release (struct inode *inode, struct file *file)
+{
+	if (atomic_dec_and_test(&bes2600_cdev.num_proc)) {
+		wake_up(&bes2600_cdev.open_wq);
+	}
+
+	bes_devel("bes2600 char device is closed\n");
+
+	return 0;
+}
+
+static struct file_operations bes2600_chardev_fops =
+{
+	.owner = THIS_MODULE,
+	.open = bes2600_chrdev_open,
+	.read = bes2600_chrdev_read,
+	.write = bes2600_chrdev_write,
+	.release = bes2600_chrdev_release,
+};
+
+#ifdef BES2600_WRITE_DPD_TO_FILE
+static int bes2600_chrdev_write_dpd_data_to_file(const char *path, void *buffer, int size)
+{
+	int ret = 0;
+	struct file *fp;
+
+	if (buffer == NULL || size == 0)
+		return 0;
+
+	fp = filp_open(path, O_TRUNC | O_CREAT | O_RDWR, S_IRUSR);
+	if (IS_ERR(fp)) {
+		bes_err("BES2600 : can't open %s\n",path);
+		return -1;
+	}
+
+	ret = kernel_write(fp, buffer, size, &fp->f_pos);
+	if (ret < 0)
+		bes_err("write dpd to file failed\n");
+
+	filp_close(fp,NULL);
+
+	bes_devel("write dpd to %s\n", path);
+
+	return ret;
+}
+
+static bool bes2600_chrdev_dpd_is_vaild(u8 *dpd_data)
+{
+	u32 cal_crc = 0;
+	u32 dpd_crc = le32_to_cpup((__le32 *)(dpd_data));
+	u32 dpd_ver = le32_to_cpup((__le32 *)(dpd_data + DPD_VERSION_OFFSET));
+
+	/* check version */
+	if (dpd_ver < DPD_CUR_VERSION)
+		return false;
+
+	cal_crc ^= 0xffffffffL;
+	cal_crc = crc32_le(cal_crc, dpd_data + 4, DPD_BIN_SIZE - 4);
+	cal_crc ^= 0xffffffffL;
+
+	/* check if the dpd data is valid */
+	if (cal_crc != dpd_crc) {
+		bes_err(
+			"bes2600 dpd data from file check failed, calc_crc:0x%08x dpd_crc: 0x%08x\n",
+			cal_crc, dpd_crc);
+		return false;
+	}
+
+	return true;
+}
+
+static int bes2600_chrdev_read_and_check_dpd_data(const char *file, u8 **data, u32 *len)
+{
+	int ret = 0;
+	u8* read_data = NULL;
+	struct file *fp;
+
+	/* open file */
+	fp = filp_open(file, O_RDONLY, 0);//S_IRUSR
+	if (IS_ERR(fp)) {
+		bes_devel("BES2600 : can't open %s\n",file);
+		return -1;
+	}
+
+#ifdef BES2600_WRITE_DPD_TO_FILE
+	if (fp->f_inode->i_size != DPD_BIN_FILE_SIZE) {
+		bes_err(
+			"bes2600 dpd data file size check failed, read_size: %lld file_size: %d\n",
+			fp->f_inode->i_size, DPD_BIN_FILE_SIZE);
+		filp_close(fp, NULL);
+		return -1;
+	}
+#endif
+
+	/* allocate memory for storing reading data */
+	read_data = kmalloc(fp->f_inode->i_size, GFP_KERNEL);
+	if (read_data == NULL) {
+		bes_devel("%s alloc mem fail\n", __func__);
+		goto err1;
+	}
+
+	/* read data  from file */
+	ret = kernel_read(fp, read_data, fp->f_inode->i_size, &fp->f_pos);
+	if (ret < DPD_BIN_SIZE) {
+		bes_err("%s read fail, ret=%d\n", __func__, ret);
+		goto err2;
+	}
+
+	/* check dpd version and crc */
+	if (!bes2600_chrdev_dpd_is_vaild(read_data))
+		goto err2;
+
+	/* close file */
+	filp_close(fp, NULL);
+
+	/* copy data to external */
+	*data = read_data;
+	*len = DPD_BIN_SIZE;;
+
+	/* output debug information */
+	bes_devel("read dpd data from %s\n", file);
+
+	return 0;
+
+err2:
+	kfree(read_data);
+err1:
+	filp_close(fp, NULL);
+	*data = NULL;
+	*len = 0;
+	return -1;
+}
+#endif
 
 const u8* bes2600_chrdev_get_dpd_data(u32 *len)
 {
+#ifdef BES2600_WRITE_DPD_TO_FILE
+	if (!bes2600_cdev.dpd_calied && bes2600_cdev.no_dpd) {
+		/* read dpd data from file that stores factory dpd calibration data */
+		if ((bes2600_chrdev_read_and_check_dpd_data(BES2600_DPD_GOLDEN_PATH,
+		   	&bes2600_cdev.dpd_data, &bes2600_cdev.dpd_len) < 0) &&
+		   (bes2600_chrdev_read_and_check_dpd_data(BES2600_DEFAULT_DPD_PATH,
+			&bes2600_cdev.dpd_data, &bes2600_cdev.dpd_len) < 0)) {
+			bes_err("%s read dpd data fail\n", __func__);
+			return NULL;
+		} else {
+			bes2600_cdev.dpd_calied = true;
+		}
+	}
+#endif
+
 	if (!bes2600_cdev.dpd_calied)
 		return NULL;
 	if (len)
@@ -325,6 +912,14 @@ int bes2600_chrdev_update_dpd_data(void)
 	}
 	spin_unlock(&bes2600_cdev.status_lock);
 
+#ifdef BES2600_WRITE_DPD_TO_FILE
+	/* write dpd data to file */
+	memset(bes2600_cdev.dpd_data + DPD_BIN_SIZE, 0, DPD_BIN_FILE_SIZE - DPD_BIN_SIZE);
+	bes2600_chrdev_write_dpd_data_to_file(BES2600_DPD_PATH,
+		bes2600_cdev.dpd_data, DPD_BIN_FILE_SIZE);
+#endif
+
+
 	return 0;
 }
 
@@ -442,48 +1037,6 @@ int bes2600_chrdev_do_system_close(const struct sbus_ops *sbus_ops, struct sbus_
 	return ret;
 }
 
-/*
- * Hard-reset the bus and wait for the bus core to remove the chip.
- *
- * Used by the firmware-wedge recovery path on platforms where the normal
- * power_switch(0) sequence has no effective chip-reset signal. The bus
- * implementation triggers an asynchronous re-detect; this helper waits for
- * the resulting remove() callback to clear bes2600_cdev.sbus_priv so that a
- * subsequent bes2600_switch_wifi(true) sees a clean state and can wait on
- * the fresh probe.
- */
-int bes2600_chrdev_do_bus_reset(const struct sbus_ops *sbus_ops, struct sbus_priv *priv)
-{
-	int ret;
-	long status;
-
-	if (!sbus_ops || !priv)
-		return -EINVAL;
-
-	if (!sbus_ops->bus_reset)
-		return -EOPNOTSUPP;
-
-	bes_info("trigger bus reset to recover wedged firmware.\n");
-
-	ret = sbus_ops->bus_reset(priv);
-	if (ret) {
-		bes_err("bus_reset failed: %d\n", ret);
-		return ret;
-	}
-
-	/*
-	 * The bus reset is asynchronous: the bus core schedules a rescan
-	 * which removes the bound function drivers and then re-detects the
-	 * chip. Wait for the remove callback to clear sbus_priv. Do not
-	 * dereference 'priv' after this point -- it may already be freed.
-	 */
-	status = wait_event_timeout(bes2600_cdev.probe_done_wq,
-				    !bes2600_cdev.sbus_priv, HZ * 3);
-	WARN_ON(status <= 0);
-
-	return 0;
-}
-
 bool bes2600_chrdev_is_wifi_opened(void)
 {
 	bool wifi_opened = false;
@@ -571,6 +1124,12 @@ void bes2600_chrdev_update_signal_mode(void)
 
 static void bes2600_chrdev_wifi_force_close_work(struct work_struct *work)
 {
+	char wifi_state[15];
+	char bt_state[15];
+	char fw_type[15];
+	char *env[] = { wifi_state, bt_state, fw_type, NULL };
+	int ret;
+
 	if (bes2600_chrdev_is_wifi_opened()) {
 		bes_devel("system exeception, force wifi down\n");
 
@@ -582,24 +1141,19 @@ static void bes2600_chrdev_wifi_force_close_work(struct work_struct *work)
 		/* unregister wifi */
 		bes2600_switch_wifi(0);
 
-		/*
+		/* power down device if wifi is only opened */
-		 * Hard exception with a bus_reset implementation: tear the
+		if (bes2600_chrdev_check_system_close()) {
-		 * bus down via mmc_hw_reset() (or equivalent) so the next
-		 * bringup probes a freshly reset chip. On PineTab2 this is
-		 * the only effective recovery path -- the existing
-		 * power_switch(0)/(1) sequence has no chip-reset signal of
-		 * its own (sdio_pwrseq owns wifi_reset).
-		 *
-		 * Soft close, or hard close on a board without bus_reset:
-		 * fall back to the legacy power_switch(0) sequence.
-		 */
-		if (bes2600_cdev.halt_dev && bes2600_cdev.sbus_ops->bus_reset) {
-			bes2600_chrdev_do_bus_reset(bes2600_cdev.sbus_ops,
-						    bes2600_cdev.sbus_priv);
-		} else if (bes2600_chrdev_check_system_close()) {
 			bes2600_chrdev_do_system_close(bes2600_cdev.sbus_ops,
 						bes2600_cdev.sbus_priv);
 		}
+
+		/* notify userspace */
+		snprintf(wifi_state, sizeof(wifi_state), "WIFI_OPENED=%d", bes2600_cdev.wifi_opened);
+		snprintf(bt_state, sizeof(bt_state), "BT_OPENED=%d", bes2600_cdev.bt_opened);
+		snprintf(fw_type, sizeof(fw_type), "FW_TYPE=%d", bes2600_cdev.fw_type);
+		ret = kobject_uevent_env(&bes2600_cdev.device->kobj, KOBJ_CHANGE, env);
+		if (!ret)
+			bes_err("bes2600 notify userspace failed\n");
 	}
 }
 
@@ -693,6 +1247,46 @@ int bes2600_chrdev_wakeup_by_event_get(void)
 
 int bes2600_chrdev_init(struct sbus_ops *ops)
 {
+	int ret = 0;
+
+	/* allocate devide id */
+	ret = alloc_chrdev_region(&bes2600_cdev.dev_id, 0, 1, "bes2600_chrdev");
+	if (ret < 0){
+		bes_err("bes2600 alloc device id fail\n");
+		ret =  -EFAULT;
+		goto fail;
+	}
+
+	/* extract major and minor device id */
+	bes2600_cdev.major = MAJOR(bes2600_cdev.dev_id);
+	bes2600_cdev.minor = MINOR(bes2600_cdev.dev_id);
+
+	/* add char device and bind operation function */
+	bes2600_cdev.cdev.owner = THIS_MODULE;
+	cdev_init(&bes2600_cdev.cdev, &bes2600_chardev_fops);
+	ret = cdev_add(&bes2600_cdev.cdev, bes2600_cdev.dev_id, 1);
+	if (ret < 0){
+		bes_err("bes2600 char device add fail\n");
+		ret =  -EFAULT;
+		goto fail1;
+	}
+
+	/* create class for creating device node */
+	bes2600_cdev.class = class_create("bes2600_chrdev");
+	if (IS_ERR(bes2600_cdev.class)){
+		bes_err("bes2600 char device add fail\n");
+		ret = -EFAULT;
+		goto fail2;
+	}
+
+	/* get char device pointer */
+	bes2600_cdev.device = device_create(bes2600_cdev.class, NULL, bes2600_cdev.dev_id, NULL, "bes2600");
+	if (IS_ERR(bes2600_cdev.device)){
+		bes_err("bes2600 char device create fail\n");
+		ret =  -EFAULT;
+		goto fail3;
+	}
+
 	/* initialise global variable */
 	atomic_set(&bes2600_cdev.num_proc, 0);
 	init_waitqueue_head(&bes2600_cdev.open_wq);
@@ -724,6 +1318,15 @@ int bes2600_chrdev_init(struct sbus_ops *ops)
 	bes_devel("%s done\n", __func__);
 
 	return 0;
+
+fail3:
+	class_destroy(bes2600_cdev.class);
+fail2:
+	cdev_del(&bes2600_cdev.cdev);
+fail1:
+	unregister_chrdev_region(bes2600_cdev.dev_id, 1);
+fail:
+	return ret;
 }
 
 void bes2600_chrdev_free(void)
@@ -733,5 +1336,9 @@ void bes2600_chrdev_free(void)
 	bes2600_free_dpd_log_buffer();
 #endif
 	bes2600_chrdev_free_dpd_data();
+	cdev_del(&bes2600_cdev.cdev);
+	unregister_chrdev_region(bes2600_cdev.dev_id, 1);
+	device_destroy(bes2600_cdev.class, bes2600_cdev.dev_id);
+	class_destroy(bes2600_cdev.class);
 	bes_devel("%s done\n", __func__);
 }

bes2600/bes_chardev.h

@@ -60,7 +60,6 @@ struct sbus_priv *bes2600_chrdev_get_sbus_priv_data(void);
 /* used to control device power down */
 int bes2600_chrdev_check_system_close(void);
 int bes2600_chrdev_do_system_close(const struct sbus_ops *sbus_ops, struct sbus_priv *priv);
-int bes2600_chrdev_do_bus_reset(const struct sbus_ops *sbus_ops, struct sbus_priv *priv);
 void bes2600_chrdev_wakeup_bt(void);
 void bes2600_chrdev_wifi_force_close(struct bes2600_common *hw_priv, bool halt_dev);
 void bes2600_chrdev_usb_remove(struct bes2600_common *hw_priv);

bes2600/bes_fw.c

@@ -125,6 +125,8 @@ int bes_host_slave_sync(struct bes2600_common *hw_priv)
 }
 */
 
+//#define DATA_DUMP_OBSERVE
+
 static int bes_firmware_download_write_reg(struct platform_fw_t *fw_data, u32 addr, u32 val)
 {
 	u8 frame_num = 0;
@@ -466,6 +468,14 @@ static int bes_firmware_download(struct platform_fw_t *fw_data, const char *fw_n
 
 const struct firmware *fw_bin;
 
+#ifdef DATA_DUMP_OBSERVE
+	char *observe;
+	size_t observe_len;
+	loff_t observe_off = 0;
+	mm_segment_t old_fs;
+	struct file *observe_file = NULL;
+#endif
+
 	struct fw_msg_hdr_t header;
 	struct fw_info_t fw_info;
 	struct download_fw_t download_addr;
@@ -573,6 +583,14 @@ retry:
 	}
 	download_addr.addr = fw_info.addr;
 
+#ifdef DATA_DUMP_OBSERVE
+	observe_file = filp_open("/lib/firmware/bes2002_fw_write.bin", O_CREAT | O_RDWR, 0);
+	if (IS_ERR(observe_file)) {
+		bes_err("create data_dump file err:%ld\n", IS_ERR(observe_file));
+		observe_file = NULL;
+	}
+#endif
+
 	while (code_length) {
 
 #if 1
@@ -622,6 +640,17 @@ retry:
 		//mdelay(5000);
 		bes_devel("tx_download_firmware_data:%x %d\n", download_addr.addr, length);
 
+#ifdef DATA_DUMP_OBSERVE
+		if (observe_file) {
+			observe = (char *)(long_buf + sizeof(struct fw_msg_hdr_t) + sizeof(struct download_fw_t));
+			observe_len = length - sizeof(struct fw_msg_hdr_t) - sizeof(struct download_fw_t);
+			old_fs = get_fs();
+			set_fs(KERNEL_DS);
+			vfs_write(observe_file, observe, observe_len, &observe_off);
+			set_fs(old_fs);
+		}
+#endif
+
 		ret = bes2600_data_write(long_buf, length > 512 ? length : 512);
 		if (ret) {
 			bes_err("tx download fw data err:%d\n", ret);
@@ -803,6 +832,11 @@ retry:
 
 err2:
 	kfree(long_buf);
+#ifdef DATA_DUMP_OBSERVE
+	if (observe_file) {
+		filp_close(observe_file, NULL);
+	}
+#endif
 err1:
 	kfree(short_buf);
 	release_firmware(fw_bin);

bes2600/bes_pwr.c

@@ -472,7 +472,6 @@ static int bes2600_pwr_enter_lp_mode(struct bes2600_common *hw_priv)
 	int i = 0;
 	struct bes2600_vif *priv;
 	int ret = 0;
-	int timeouts = 0;
 	char ip_str[20];
 	unsigned long status = 0;
 
@@ -529,35 +528,22 @@ static int bes2600_pwr_enter_lp_mode(struct bes2600_common *hw_priv)
 				if (ret) {
 					atomic_set(&hw_priv->bes_power.pm_set_in_process, 0);
 					bes_err("%s, set operation mode fail\n", __func__);
-					timeouts++;
-					continue;
 				}
 
 				/* wait power save mode changed indication */
 				status = wait_for_completion_timeout(&hw_priv->bes_power.pm_enter_cmpl, 5 * HZ);
 				atomic_set(&hw_priv->bes_power.pm_set_in_process, 0);
 				reinit_completion(&hw_priv->bes_power.pm_enter_cmpl);
-				if (!status) {
+				if (!status)
-					bes_devel("%s, wait pm ind timeout\n", __func__);
+					bes_err("%s, wait pm ind timeout\n", __func__);
-					timeouts++;
-				}
 			} else {
 				bes_devel("skip enter lp mode\n");
 			}
 		}
 	}
 
-	/*
+	/* set device low power configuration */
-	 * Enter the device-end of the LP transition only if every per-VIF
-	 * mac80211 handshake reached firmware-ACKed completion. Doing the
-	 * device-LP setup while any VIF is still pending leaves the driver
-	 * in an inconsistent state that cascades into SDIO TX errors on
-	 * the BES2600.
-	 */
-	if (timeouts == 0)
 	bes2600_pwr_device_enter_lp_mode(hw_priv);
-	else
-		ret = -ETIMEDOUT;
 
 	return ret;
 }

bes2600/main.c

@@ -790,6 +790,41 @@ void bes2600_core_release(struct bes2600_common *self)
 	return;
 }
 
+#if (GET_MAC_ADDR_METHOD == 2) || (GET_MAC_ADDR_METHOD == 3) /* To use macaddr and ps mode of customers */
+int access_file(char *path, char *buffer, int size, int isRead)
+{
+	int ret=0;
+	struct file *fp;
+	mm_segment_t old_fs = get_fs();
+
+	if(isRead)
+		fp = filp_open(path,O_RDONLY,S_IRUSR);
+	else
+		fp = filp_open(path,O_CREAT|O_WRONLY,S_IRUSR);
+
+	if (IS_ERR(fp)) {
+		bes_err("BES2600 : can't open %s\n", path);
+		return -1;
+	}
+
+	if (isRead) {
+			fp->f_pos = 0;
+			set_fs(KERNEL_DS);
+			ret = vfs_read(fp,buffer,size,&fp->f_pos);
+			set_fs(old_fs);
+	} else {
+			fp->f_pos = 0;
+			set_fs(KERNEL_DS);
+			ret = vfs_write(fp,buffer,size,&fp->f_pos);
+			set_fs(old_fs);
+	}
+	filp_close(fp,NULL);
+
+	bes_info("BES2600 : access_file return code(%d)\n", ret);
+	return ret;
+}
+#endif
+
 int bes2600_wifi_start(struct bes2600_common *hw_priv)
 {
 	int ret = 0, if_id;

bes2600/sbus.h

@@ -75,14 +75,6 @@ struct sbus_ops {
 	void (*halt_device)(struct sbus_priv *self);
 	bool (*wakeup_source)(struct sbus_priv *self);
 	int (*reboot)(struct sbus_priv *self);
-	/*
-	 * Force the host bus to re-detect and re-probe the chip. Called
-	 * from the firmware-wedge recovery path when power_switch() has no
-	 * effective chip-reset signal of its own (e.g. PineTab2, where the
-	 * wifi-reset GPIO is owned by sdio_pwrseq, not the bes2600 node).
-	 * Returns 0 on success or a negative errno.
-	 */
-	int (*bus_reset)(struct sbus_priv *self);
 };
 
 void bes2600_irq_handler(struct bes2600_common *priv);

bes2600/scan.c

@@ -14,50 +14,11 @@
 #include "scan.h"
 #include "sta.h"
 #include "pm.h"
-#include "epta_coex.h"
 #include "epta_request.h"
 #include "bes_pwr.h"
 
-/*
- * After this many consecutive WSM scan rejections from firmware, stop
- * issuing new scans for BES2600_SCAN_BACKOFF_JIFFIES and let the state
- * that's rejecting them (coex window, firmware-internal busy) clear.
- */
-#define BES2600_SCAN_REJECT_THRESHOLD	3
-#define BES2600_SCAN_BACKOFF_JIFFIES	(10 * HZ)
-
 static void bes2600_scan_restart_delayed(struct bes2600_vif *priv);
 
-/*
- * Decide whether to skip sending the next WSM scan command without
- * bothering the firmware. Two triggers:
- *
- *  1. BT A2DP is streaming in non-FDD coex mode. The firmware is
- *     known to reject scan requests during that window; short-
- *     circuiting here saves a WSM round-trip and avoids the
- *     wsm_generic_confirm / scan_work warning cascade that follows.
- *
- *  2. We already saw >= BES2600_SCAN_REJECT_THRESHOLD consecutive
- *     rejections on recent scan attempts and the backoff window has
- *     not yet elapsed. Whatever was rejecting them is likely still
- *     rejecting them; give it time.
- *
- * Returns true if the caller should abandon the scan iteration.
- */
-static bool bes2600_scan_should_defer(struct bes2600_common *hw_priv)
-{
-#ifdef WIFI_BT_COEXIST_EPTA_ENABLE
-	if (!coex_is_fdd_mode() && coex_is_bt_a2dp())
-		return true;
-#endif
-
-	if (hw_priv->scan.reject_count >= BES2600_SCAN_REJECT_THRESHOLD &&
-	    time_before(jiffies, hw_priv->scan.backoff_until))
-		return true;
-
-	return false;
-}
-
 #ifdef CONFIG_BES2600_TESTMODE
 static int bes2600_advance_scan_start(struct bes2600_common *hw_priv)
 {
@@ -741,29 +702,10 @@ void bes2600_scan_work(struct work_struct *work)
 				wsm_unlock_tx(hw_priv);
 		} else
 #endif
-		{
-			if (bes2600_scan_should_defer(hw_priv)) {
-				hw_priv->scan.status = -EBUSY;
-				hw_priv->scan.reject_count++;
-				hw_priv->scan.backoff_until =
-					jiffies + BES2600_SCAN_BACKOFF_JIFFIES;
-				wiphy_dbg(priv->hw->wiphy,
-					  "[SCAN] deferred (coex/backoff, reject_count=%u)\n",
-					  hw_priv->scan.reject_count);
-				kfree(scan.ch);
-				goto fail;
-			}
 			hw_priv->scan.status = bes2600_scan_start(priv, &scan);
-		}
 		kfree(scan.ch);
-		if (hw_priv->scan.status) {
+		if (WARN_ON(hw_priv->scan.status))
-			hw_priv->scan.reject_count++;
-			hw_priv->scan.backoff_until =
-				jiffies + BES2600_SCAN_BACKOFF_JIFFIES;
-			/* Lower callers already logged the reason at wiphy_warn. */
 			goto fail;
-		}
-		hw_priv->scan.reject_count = 0;
 		hw_priv->scan.curr = it;
 	}
 	up(&hw_priv->conf_lock);

bes2600/scan.h

@@ -42,17 +42,6 @@ struct bes2600_scan {
 	struct delayed_work probe_work;
 	int direct_probe;
 	u8 if_id;
-	/*
-	 * Track consecutive firmware-side WSM scan rejections so we can
-	 * back off briefly instead of re-issuing the same scan on every
-	 * mac80211 background-scan tick. Firmware returns WSM status != 0
-	 * for a handful of transient conditions (BT A2DP active in non-
-	 * FDD coex, firmware-internal busy windows) and keeps rejecting
-	 * until the state clears; retrying at full cadence just floods
-	 * dmesg.
-	 */
-	unsigned int reject_count;
-	unsigned long backoff_until;
 };
 
 int bes2600_hw_scan(struct ieee80211_hw *hw,

bes2600/wsm.c

@@ -134,20 +134,8 @@ static int wsm_generic_confirm(struct bes2600_common *hw_priv,
 				 struct wsm_buf *buf)
 {
 	u32 status = WSM_GET32(buf);
-
+	if (WARN(status != WSM_STATUS_SUCCESS, "wsm_generic_confirm ret %u", status))
-	/*
-	 * A non-SUCCESS status here is a firmware-side policy decision for
-	 * the command whose confirm this is -- commonly WSM status 2 for
-	 * scan (0x0407) rejected because of a coex window or transient
-	 * firmware-busy state. It is not a driver/kernel bug, so avoid the
-	 * WARN()/stack-trace treatment; the caller already emits a
-	 * wiphy_warn identifying the request id and will propagate the
-	 * error to mac80211.
-	 */
-	if (status != WSM_STATUS_SUCCESS) {
-		bes_devel("%s ret %u\n", __func__, status);
 		return -EINVAL;
-	}
 	return 0;
 
 underflow:

bes2600/wsm.h

@@ -2236,5 +2236,7 @@ int wsm_cpu_usage_cmd(struct bes2600_common *hw_priv);
 
 int wsm_wifi_status_cmd(struct bes2600_common *hw_priv, uint32_t status);
 
+#if defined(STANDARD_FACTORY_EFUSE_FLAG)
 int wsm_save_factory_txt_to_mcu(struct bes2600_common *hw_priv, const u8 *data, int if_id, enum bes2600_rf_cmd_type cmd_type);
+#endif
 #endif /* BES2600_HWIO_H_INCLUDED */

debian/copyright

@@ -18,7 +18,8 @@ License: LGPL-2.1
  License for more details.
  .
  You should have received a copy of the GNU Lesser General Public License
- along with this library; if not, see <https://www.gnu.org/licenses/>.
+ along with this library; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
  .
  On Debian systems, the full text of the GNU Lesser General Public License
  version 2.1 can be found in the file "/usr/share/common-licenses/LGPL-2.1".