test0r
51d46a2e25
The previous patch ("bes2600: gate PM indication completion on pending
request and track chip state") added enum bes2600_chip_pm_state and the
chip_pm_state field tracking what the host has *seen the firmware
confirm*. This patch makes the wake side use it.
Without this, every bes2600_pwr_device_exit_lp_mode() unconditionally
runs gpio_wake() + sbus_active() + wsm_set_operational_mode(active),
even when the chip is already in confirmed-ACTIVE state and the wake
sequence has nothing to do. The visible failure mode on PineTab2:
bes2600_pwr_enter_lp_mode, wait pm ind timeout
repeat set gpio_wake_flag, sub_sys:0
bes2600_sdio_active failed, subsys:0
bes2600_pwr_device_exit_lp_mode, active mcu fail
cycling every ~9 s, ~22 cycles in 10 minutes. Three pieces:
1. enter_lp_mode timed out (firmware indication lost). With c6.1,
chip_pm_state is now UNKNOWN.
2. lock_device fires exit_lp_mode.
3. gpio_wake hits "bit already set" because device_enter_lp_mode
was skipped when the indication timed out, so gpio_sleep was
never called - the bit reflects driver intent, not chip state.
gpio_wake silently no-ops (no GPIO edge), bit stays set.
4. sbus_active spends 200 x 2 ms looking for MCU_WAKEUP_READY that
never comes (firmware was never told to wake), then fails.
5. Driver continues to wsm_set_operational_mode against the wedged
bus, compounding the failure.
This patch's three moves:
* bes2600_pwr_device_exit_lp_mode() reads chip_pm_state at entry.
On BES2600_CHIP_PM_ACTIVE, log at devel level and return without
touching gpio_wake / sbus_active / WSM. The chip is in the state
we want; the handshake exists only to drive a transition.
* On BES2600_CHIP_PM_LP or BES2600_CHIP_PM_UNKNOWN, run the wake
handshake as before, but on sbus_active() failure: set
chip_pm_state = UNKNOWN, log once at err level, and bail out.
Do NOT call wsm_set_operational_mode over a wedged bus - it
would just emit a second error and leave the chip in an even
less defined state.
* bes2600_gpio_wakeup_mcu() / bes2600_gpio_allow_mcu_sleep():
demote "repeat set/clear gpio_wake_flag" from bes_err to
bes_devel. Multi-subsystem wake-hold (e.g. WIFI + BT both want
MCU awake) is the steady-state case, and the symmetric clear
while bit-already-clear is racy bookkeeping rather than a
hardware error. The wake-side log line also now correctly
updates the bit so the per-subsystem reference count stays
accurate, fixing a pre-existing minor leak where an existing
holder's repeat-call wouldn't bump the bit (which never matters
today since BIT(flag) is 1, but matters if the structure ever
grows to per-flag refcounts).
Net effect on the cycle:
* If chip is genuinely ACTIVE (chip_pm_state == ACTIVE), wake skips
cleanly. Storm goes silent.
* If chip is genuinely LP, behaviour is unchanged.
* If chip is UNKNOWN (post-timeout state), one wake attempt is
made; on failure, state stays UNKNOWN and we don't emit a
second cascade error per attempt. Repeated UNKNOWN with failed
wake will eventually be picked up by the LMAC active-monitor
and escalated to mmc_hw_reset (c5.2).
No new locks, no new state. Only consumption of the chip_pm_state
field added in the prerequisite patch.
Signed-off-by: Markus Fritsche <fritsche.markus@gmail.com>